I would use heat. A hairdryer aimed at the socket for a few minutes=2C and
get someone else to pull on the wing.Karl
Subject: Re: Europa-List: Spar won't come off the socket!!
From: peterz@zutrasoft.com
Date: Sun=2C 22 Sep 2013 15:37:46 -0400
Along the same lines=2C how about a thin gauge SS safety wire ( if it was t
he side face that is glued )-Pete A239
On Sep 22=2C 2013=2C at 3:17 PM=2C Alan Burrill <alanb@dpy01.co.uk> wrote:
Is there enough clearance to slide a knife blade between the spar and socke
t? If you sight down the pin hole when you do it you might just be able to
see what the problem is an maybe even cut through it!
Alan
Sent from my iPad
On 22 Sep 2013=2C at 19:54=2C Andrew Sarangan <asarangan@gmail.com> wrote:
I am hoping someone will have a great idea to solve this problem. I just fi
nished gluing the spar sockets=2C but I am unable to withdraw the port spar
out of the starboard socket. I was able to get the bolts out quite easily.
It also doesn't look like the spar got glued to anything=2C because I am a
ble to rotate the spar=2C and wiggle it just but it won't slide out of the
socket. What I suspect is that some flox might have oozed into the inside f
ace of the socket which and might be preventing the bushing from sliding ou
t. I greased everything=2C but did not grease the inside faces of the socke
ts. If all fails I was going to cut the outer face of the socket to extrac
t the spar. Perhaps I could reglue that face back in place. Any ideas would
be appreciated.=0A
=0A
=0A
=0A
=0A
=0A
D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3
D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3
D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3
D=0A
a-List"">http://www.matronics.com/Navigator?Europa-List=0A
D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3
D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3
D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3
D=0A
//forums.matronics.com=0A
D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3
D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3
D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3
D=0A
ot=3B">http://www.matronics.com/contribution=0A
D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3
D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3
D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3
D=0A
=0A
=0A
=0A
=0A
D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3
D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3
D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3
D=0A
a-List"">http://www.matronics.com/Navigator?Europa-List=0A
D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3
D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3
D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3
D=0A
//forums.matronics.com=0A
D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3
D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3
D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3
D=0A
ot=3B">http://www.matronics.com/contribution=0A
D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3
D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3
D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3
D=0A
=0A
=0A
=0A
=0A
============0A
============0A
============0A
============0A
=0A
|