To all fuel tank concerns
Europa has 25 tanks on order, however, the mold was damaged / discarded
by the manufacturer. The new tank, made by Roger and John that I have
---From 2009, holds a bit more fuel (I have 20 gallons useable in my
trigear filled to the brim) and has reinforcements in addition to the
normal support tabs. I am not privy to the new tank manufacturers mold
to see that it is exactly the same. Karen expects delivery in a couple
weeks, but it will have to undergo QC first. I am watching and waiting
for a tank also for a new customer.
For those attempting to build a fiberglass composite tank using the old
tank as a mold, I believe the molding in place to be more time consuming
than just pulling the old tank and replacing it with the new tank and
properly supporting it.
Fiberglass tanks, as pointed out by Graham, have problems with auto
fuel.
No fiberglass tank (epoxy, vinylester, or polyester) holds up with Auto
Fuel with Ethanol. The marine industry coats the inside of fiberglass
tanks with specialized coatings to protect the fiberglass from auto fuel
additives and ethanol. It appears AV Gas is safe with all fiberglass
tanks. However, the AV Gas formula is under review by the FAA for
changes, so no guarantees.
Repairs to the current tank is difficult. Epoxy and glass stick very
well to the PTFE tank material. Jeff Roberts has successfully repaired
his tank, but it depends where your crack is. I have repaired the top
of the tank with glass and pro seal. Note, that proseal softens with
time when exposed to ethanol, but has not failed so far. The problem
with glass repairs to the tank, in my opinion, is that the bond has less
peel strength than ideal and under flexing and pressure will eventually
fail.
I believe, and have put my money where my mouth is, that the solution to
the tank cracking is the support structure used for the tank.
For those of you who haven't seen my previous posts, I have attached one
of my drawings to show what I mean. The front of the tank is totally
unsupported from the area above the spars (the ledge) to the bottom rear
of the tank. Tank flexing of the older and thinner tank will force the
tank to eventually crack at the areas that are glassed hard and not
allowed to move. Whether the tank gets brittle with age, from the
fiberglass interface, gets brittle with being left empty during long
repairs, or what, I really don't care, as all poly tanks will flex, and
going from empty to full will cause a flex of a tank and eventually, if
forced back and forth, will fail.
Metal cracks also unless properly supported, has condensation problems ,
and it is expensive for odd shaped tanks to build, fiberglass has its
fuel compatibility problems, molding issues, etc., and PTFE or poly
tanks have their long term problems unless properly supported.
What has my company done?
Defined how to support the tank. We do not glass the tank directly to
the cockpit module structure per the instruction manual. We put release
plastic between the required build manual supports and tank to prevent
the required supports from sticking permanently and creating a stress
riser. We use glass tabs to secure it at the top, for fore/aft and side
to side movement. Polyurethane foam is used to secure the tank from
shifting, and we carefully build lower tank supports. (On a new build
it means fitting the module a couple more times to fit an expand cell
pad laid along the bottom of the tank perimeter covered with 2 mil
plastic to define where the tank sits and requires support. The expand
cell is then sanded to final shape and glassed over making a very good
support.) The tank also sits on a cork support for padding (kind of
overkill) to prevent wear, but plastic works OK also. This means the
tank is supported vertically and horizontally by the saddle, the bottom,
the front ledge, and foam wedged with urethane foam to prevent movement
fore, aft , up , or down. All weight is carried by a combination of the
floor and the bulkheads.
Existing tanks have added non expanding polyurethane foam sprayed under
the tank to support the bottom, but this is not ideal as I prefer a
longeron and ribs be glassed to the floor for the tunnel area and across
the front of the tank for vertical support. This adds support for the
tank bottom, back and sides as opposed to the previous supports which
hung the tank solely off the bulkheads...
Other bandaids:
We have a plastic welder and have tried it recently on PTFE tanks used
in commercial lawn equipment (which are poorly supported fuel tanks and
prone to cracking with age) and have had success so far. Not an exact
science but we have also done an auto radiator, and a auto overflow
coolant tank to see what the long term effects are. We are concerned
that the heat stress near the weld may be brittle and fail, so time will
tell. Pulling the tank and welding is not cost effective as one may as
well drop in another tank.
In the mean time, I am waiting for a new tank to drop in as that is the
easiest of all solutions, as the tank supports can be put in quite
easily through the hole in the top of the module. This I believe will
solve the problems of stress risers and tank failures. Anyone can
replace a tank in less than a week.
Regards,
Bud
----- Original Message -----
From: Nic<mailto:scouttwo@sbcglobal.net>
To: europa-list@matronics.com<mailto:europa-list@matronics.com>
Sent: Saturday, September 24, 2011 12:17 AM
Subject: Re: Europa-List: Can we borrow your tank?
<scouttwo@sbcglobal.net<mailto:scouttwo@sbcglobal.net>>
Fred,
I have read the stories of failing fuel tanks while landing in trees.
While a challenging feat to be sure, the tank shouid still not fail.
Aluminum would suffice but I already have one sized to fit.
I always figured the inner layer bonds with the outer layer throught
the
holes.
This should encase the plastic which now would merely provide the
shape.
I think I would also make a removeable lid panel to mount all tank
access
through.
I have several motorcycle fuel pumps for 50 psi output for my CBR
engine.
Nic :)
http://www.matronics.com/Navigator?Europa-List<http://www.matronics.com/N
avigator?Europa-List>
http://www.matronics.com/contribution<http://www.matronics.com/contributi
on>
|