Gidday,
So, I've tried using a second incompressible, but am now concerned I have do
ne that correctly. I placed the second one up against the other one, and as t
hey compress, we know they exude outward, even a little bit. I reckon the ca
ble I between the 2 could now be under tension, continually, and possibly qu
ite a lot. Whatever stress it is preloaded is an equivalent weight, which in
essence would minimise the stress loading on the cable.
I've Lao got cable kicking around that looks more like gal than Stainless St
eel, but I know I have only ever bought the right stuff 7x7 3/32" dia contro
l cable. Is there a reason why over time Stainess Steel cable can go dull o
ver time?
Tony Renshaw
Sent from my iPad
> On 1 Mar 2014, at 9:52 am, Tim Ward <ward.t@xtra.co.nz> wrote:
>
> Yes I did. The 25mm long tail Richard talks about, instead of using tape I
use an additional sleeve.
> Tim
>
> Tim Ward
> 12 Waiwetu Street
> Fendalton,
> Christchurch, 8052
> New Zealand.
>
> ward.t@xtra.co.nz
>
> Ph 64 3 3515166
> Mob 0210640221
>
>
>> On 1/03/2014, at 11:22 am, Tony Renshaw <tonyrenshaw268@gmail.com> wrote:
>>
>> Hi Tim,
>> So did you use two on all the ends, from pedal all the way thru to rudder
?
>> TR
>>
>>> On 1 Mar 2014, at 8:52, Tim Ward <ward.t@xtra.co.nz> wrote:
>>>
>>> Tony,
>>> As Richard stated, I used two Nicopress Sleeves for " peace of mind".
>>> Good recommendation.
>>> Tim
>>>
>>> Tim Ward
>>> 12 Waiwetu Street
>>> Fendalton,
>>> Christchurch, 8052
>>> New Zealand.
>>>
>>> ward.t@xtra.co.nz
>>>
>>> Ph 64 3 3515166
>>> Mob 0210640221
>>>
>>>
>>>> On 1/03/2014, at 6:39 am, "richard" <rcollings@talktalk.net> wrote:
>>>>
>>>> Hi Tony You must leave an inch long tail after the sleeve and shrink a
short length of electric wire sleeving on to that end for protection.
>>>> Two things you can do also, conduct a proof load test, I don=99t k
now the loads but Europa may, or you could drop an email to Andy Draper at t
he LAA engineering dept he would know. The other way of being certain is to b
uild the cables with two Nicopress sleeves on each end. I know its more weig
ht but =9CPiece of mind=9Dis worth a few ounces .
>>>> Best of luck
>>>> Richard
>>>>
>>>> From: Tony Renshaw
>>>> Sent: Friday, February 28, 2014 10:41 AM
>>>> To: europa-list@matronics.com
>>>> Subject: Europa-List: Nicopress Squeezes Using Aviation Approved Squeez
er......comments requested .
>>>>
>>>> Gidday,
>>>> I=99ve attached 2 photos of my Nicopress squeezes, and 1 of the j
aws of the tool. Any input gratefully received.
>>>> Regards
>>>> Tony Renshaw
>>>>
>>>>
>>>>
>>>>
>>>>
>>>> <2014_02_28_Distorted_Nicopress-12.jpeg><2014_02_28_Squeezed_Nicopress_
End-14.jpeg>
>>>>
>>>> <2014_02_28_Nicopress_Crimper_Jaws-11.jpeg>
>>>>
>>>> No virus found in this message.
>>>> Checked by AVG - www.avg.com
14
>>>>
>>>
>>>
>>> D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3
D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D
>>> a-List"">http://www.matronics.com/Navigator?Europa-List
>>> D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3
D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D
>>> //forums.matronics.com
>>> D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3
D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D
>>> ot;">http://www.matronics.com/contribution
>>> D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3
D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D
>>>
>>
>>
>> D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3
D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D
>> a-List"">http://www.matronics.com/Navigator?Europa-List
>> D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3
D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D
>> //forums.matronics.com
>> D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3
D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D
>> ot;">http://www.matronics.com/contribution
>> D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3
D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D
>>
>
>
3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3
D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D
=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D
3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3
D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D
=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D
3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3
D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D
=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D
3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3
D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D
=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D
>
|