Keith Try SP Systems Aust, 4b Wilmette Pl, Mona Vale NSW 2103 Aust. Phone 02 9979 6378 Been a couple of years since I bought though. They have another type for finishing that I have not tried. Best W
Congratulations John Got the message way over here in Oz. Copying this to my chauffeur for the day I visited about a year back. Looking forward to hearing more in due course. Sincerely JR (Bob) Gowin
Congratulation Jac And done in only 8 years with a commendation from Ivan! - I have 10 up already and a lot more to go. Get in the saddle and go for it. JR (bob) Gowing UK Kit 327 in Oz -- Original M
Dear All As another idea - I modelled a seat by laying 4 plies of bid over a cheap plastic chair with good back support as used in public buildings. To support the back I cut a pair of slots on the b
Rowland I am interested in checking my leading edge with a profile but I could not open the file either because I don't have any special programs. I guess if we had say an Excel file of coordinates c
Duncan and Fellows I can't imagine why any locking of the nut is needed either; the pin is tight with Loctite and the nut will be encased in the flox mix so cannot turn. You would have to heat the pi
David or anyone I could not find the modified version of Mod 74 on the Factory Web site under Mod 74 so -- Just where did Europa post the modified version of Mod 74 Wing Pin Replacemet please?) To an
Nigel Thank you for the tip just in time! JR (Bob) Gowing in Oz -- Original Message -- From: nigel charles To: Forum Europa Sent: Wednesday, September 12, 2007 9:34 PM Subject: Europa-List: Mod 74 I
Dear Jeff I am not a guru but I believe the materails last for years; but unfortunately you can't prove it without testing gear. I am using some 1996 Ampreg for my filling and still have 4 cans of re
David I will be in the same position with kit 327. Maybe we just have to use a thin nylon tube on our supplies of thinner and Loctite 603 and try to get the end in a position to deposit the two in tu
Fred Your headrest looks fantastic! I think it is the best solution I have seen yet. Looking forward to seeing a lot more of it! JR (Bob) Gowing UK Kit 327 in Oz -- -- -- -- -- 8:34 PM
Rowland and Craig I still have some containers of Ampreg 20 but no hardener which I had thrown out when the containers looked as if they had leaked. When I tried to get Ampreg hardener (now from Guri
K Yes, I had not looked. It seems a pity that we don't have an Aussie co-ordinator to collect the list etc - But I am not volunteering! Just unloading the Chapter 23 Secretary's job to Bob Phillips e
K YOu are right on to it! JR -- Original Message -- From: "Kingsley Hurst" <hurstkr@redzone.com.au> Sent: Tuesday, December 11, 2007 11:40 PM Subject: Re: Europa-List: Secondary Fuel Pump, correct or
Fellow builders My study of Mod 73 tells me that we are to put a 10mm piece of masking tape on the underneath face of the TP6's to cover the hole and then two layers of bid (1" squares) perhaps added
Dear Gerry Thank you for your detailed reply but yes I rember I had aheard of the gauge but thought it was to be installed within the tank and I did not want to cut into the tank. And thank you also
Craig Tony Krzyzewski's site mayh interest you if you have never looked at it..... Electronic Fuel gauge fitted. Builder developed modification Don't quite know what you were thinking but if I were c
Craig I have been using the A420 I got with the kit in about 1966 and believe the conponents are long lasting - but now that you have spoken I will run at t est before next use. JR (Bob) Gowing UK Ki