Gidday, My battery charger, a CTEK XS800 trickle charger, has a wide range of accessories, including a panel mounted display that simply flashes either a Green, Orange, or Red LED, at a frequency of
Gidday, Quick question.why cant I tidy up a nicopress and squeeze it 90 degrees rotated after the first squeeze, to tidy the compress? If the first squeeze is correct, the second squeeze shouldnt dis
Hi Rowland, Thank you for your reply. I only vaguely remember the 3 crimps. I have a big squeezer, like a set of bolt cutters. It has about 5 positions, so you choose the one you want, position a lit
Gidday, Like others I am considering whether I will close off the end of my flaps. I have found a tube that is tapered down to the OD of the flap cross tube, my vacuum cleaner wand, and I have create
Hi Graham, Not stabilising doesn=92t sound good. Seems like using good old blue foam might be the better way to go, and bog it in with micro. It is a frustration that you can=92t poor in a liquid tha
Hey, Sensai FK.....you can't climb down from my pedestal that easily! I could never have made those complex curves as diligently. I struggled to simply glue them together =F0=9F=98=9C Tony R Sent fro
Hi William, I am not sure from your explanation, and I dont have the book with me, but I roughed up the gluing inner face of my aileron bell crank quick connect, using my Dremel and a Permagrit drum
Hi Tim, So did you use two on all the ends, from pedal all the way thru to rudder? TR hort length of electric wire sleeving on to that end for protection. ow the loads but Europa may, or you could dr
Gidday, So, I've tried using a second incompressible, but am now concerned I have do ne that correctly. I placed the second one up against the other one, and as t hey compress, we know they exude out
Hi Lance, Thanks for responding. That looks a great tester. With the various holes, did you do the maths to calculate and what is the formula you use? Good setup. I am impressed. I believe you are cl
Hi Lance, What powerplant are you using again? I am wondering whether I fit my flap floor hinge hardware at this stage, or just rely on the redux pads, and put them in later? I figure filling and pai
Gidday, I have gone through my fair share of cable, and consequently I have bits everywhere. I have a roll of cable which appears to be galvanised, or really dull Stainless Steel, which I believe doe
Hi Graham, Wish I knew if it was what was supplied by Europa. I=92ve had the kit too long to know, things have been moved around, and I don=92t recall the Europa stuff ever being labelled. Maybe some
Hi Richard, So yours must be the dull stuff too? I'll check the ACS catalogue again, but I thought that's all they sold, the Stainless Steel stuff. Funny that it's O k in the US, where most of the wo
Gidday, Ive heard it mentioned that to extend this step back a bit might make things more comfortable. Can I get an input on what dimension is recommended? Ive heard about 75 mm would do it, and I wi
Hi Craig and co. I want to put 75 mm onto the shelf, bringing it aft into the footwell, to give me a place for my heels. Is that a dumb idea because only being 5 9 or 175 cm, I think my legs will eas
hi Gerry, I have no clue what aluminium =93rice=94 plate is. Look forward to the photos. Thanks. TR I'll see if I can find photos. wrote: footwell, to give me a place for my heels. Is that a dumb ide
Hi Bob, I know what an "I" section is, but I just can't imagine what you mean. If you said "L" shape, to protect the Trailing edge of the rudder pedal attachment shelf, I would have been with you, bu
Hi, This is my TPDD. You can=92t really tell from the photo but the top of the tunnel has been turned into a hinged lid to the underside, where fuel selectors, pumps, etc are to be located. I have an