Hi, I today sat in the europa with a hand held , engine running - & non running, and varius circuit breaker configurations, it appears that i have been to quick to blame the Airmaster Prop., the inte
Hiello, Just had the towbar back from a local engineering firm and it works very well, it uses all the stock facory nosewheel axle components plus the addition of two ally sockets, http://www.europao
Hello Peter, Apologies for the delay been away with the wife and kids for the weekend so unable to reply, It was made by Spencer Davies Engineering , www.sde.co.uk , Im sorry but I dont Have a price,
Hello Danni , Apologies for the delay been away with the wife and kids for the weekend so unable to reply, It was made by Spencer Davies Engineering , www.sde.co.uk , Im sorry but I dont Have a price
Hello Kingsley, what have you done on the fuselage where it is met by the Wing Root, is it an optical illusion or have you moulded an extrusion to meet the wing root? Steve #573 Visit - www.EuropaOwn
Hi Frans, Mine was exactly as you describe, i just did my best with it. its difficult to notice when its all together and painted, i'll see if i can get a picture uploaded, Steve. Visit - www.EuropaO
Author: stephen vestuti <s@vestuti.orangehome.co.uk>
Date: Fri, 26 Aug 2011 10:36:24
Jeff - Baby Blue , Hi, I notice your comment about " a leaky exhaust that might allow heat to get to the carb bowls ". I had this problem on the first Europa that I built , the fuel boiling in the St
Author: stephen vestuti <s@vestuti.orangehome.co.uk>
Date: Sun, 4 Sep 2011 11:56:33
Thanks for the replies, would you have any pictures of that arrangement? Steve #630 Read this topic online here: http://forums.matronics.com/viewtopic.php?p=351390#351390
Author: stephen vestuti <s@vestuti.orangehome.co.uk>
Date: Sat, 10 Sep 2011 13:08:30
Hi Grahame, Try pulling the Stb. "Allen" Pin to only go through the first spar, then push the Port Spar Pin, when it's fully home, repush the Stb. Allen Pin, Try that sequence and see how you get on,
Author: stephen vestuti <s@vestuti.orangehome.co.uk>
Date: Thu, 22 Sep 2011 03:09:19
Hi All, Does any one know what materials are needed to manufacture a "clear lens" for a wing tip Nav light. Cliff Shaw managed it here http://www.europaowners.org/forums/gallery2.php?g2_itemId=26047
Author: stephen vestuti <s@vestuti.orangehome.co.uk>
Date: Thu, 22 Sep 2011 08:21:51
Thanks Graham, It sounds like its going to be a challenge. I'm looking forward to it. If you or anyone knows of a "kit" supplier to make a clear lens then please pass on the link to me, Thanks, Steve
Author: stephen vestuti <s@vestuti.orangehome.co.uk>
Date: Sun, 25 Sep 2011 13:01:24
Excellent report Bud and thanks for passing the information on, Steve, Read this topic online here: http://forums.matronics.com/viewtopic.php?p=353180#353180
Author: stephen vestuti <s@vestuti.orangehome.co.uk>
Date: Mon, 3 Oct 2011 07:43:58
Well that's good timing Ian! I have just completed a series of drawings of various Mods to submit to the LAA and one of them was the wing conduit Mod! Thank you for bringing that up. I will need to c
Author: stephen vestuti <s@vestuti.orangehome.co.uk>
Date: Mon, 10 Oct 2011 10:21:17
I too have been researching the comms. for some time. The Garmin SL40 doesn't support 8.33 but does talk to the MGL Efis that i'm fitting. (change frequency from the Efis screen) The XCom 760 doesnt
Author: stephen vestuti <s@vestuti.orangehome.co.uk>
Date: Mon, 10 Oct 2011 13:57:11
I had already looked at the MGL VHF 10, it too doesn't appear to support 8.33 channel spacing and is stuck on 25KHz, maybe 8.33 is not that important... It talks to the Efis though, Steve. Read this
Author: stephen vestuti <s@vestuti.orangehome.co.uk>
Date: Tue, 11 Oct 2011 01:32:20
Thanks for bringing that up Frans. It appears that MGL have launched a new radio called the V6 which does support 8.33 and communicates with the Efis, I'd only seen the V10, good old forum, Steve. Re
Author: stephen vestuti <s@vestuti.orangehome.co.uk>
Date: Tue, 11 Oct 2011 12:37:20
Richard, well thats great. I've taken another look at the manual and can't find any mention of external frequency change , do you have the pin numbers that you connect to on the D-Connector? Steve. R