Hi Bob Most of the info is in this document, If you need more information give me a call. Regards Ivor _____ From: owner-europa-list-server@matronics.com [mailto:owner-europa-list-server@matronics.co
Hi Fred I used a vent valve TRV86 in the top of the filler with a AN fitting taken down to just forward of the flap tube, http://www.thinkauto.com/ information on web site sent photo's direct! regard
Hi Paul I have done something similar to Svien but made the pod to accommodate a S.I.R Pegasus compass, Regards Ivor Anyone got ant photos of where they have mounted a compass ( along with which mode
Paul Aprox 2 1/2 litres at 50/50% Regards Ivor Hi All, I am about to drain my Evan coolant and replace it wth a regular coolant and the new Rotax pressure cap. I have two questions for the list. Does
Hi Ferg I fitted the MAP sensor to the interior Firewall, Then used a bulkhead pipe fitting to carry the vacuum through the firewall using Silicone Vacuum pipe to the cross balance pipe between carbu
Hi David You will have to register again. The passwords are in scripted and cannot be retrieved, Regards Ivor I have forgotten my user name and password and cannot enter the site to change me email a
Jos If you put a small restrictor in the feed to the Map sensor it will smooth out the pulses so the Dynon can handle the fluctuation , Regards Ivor The D180 map is a bit jumpy, too sensitive, wherea
Hi John Skydrive our UK Rotax Distributor sell a Keywest regulator, http://www.skydrive.co.uk/sd_sa_ie.asp These are made in the US so might be useful to you, You will have to check for there suitabi
Congratulations Peter! Very well done, It must be fantastic completing your project in only 5 years :-) I am hoping to follow shortly after 7 Warmest regards Ivor I am proud to announce that G-CHOX t
Hi Kevin If you are in the UK They are available from http://rswww.com/cgi-bin/bv/rswww/searchBrowseAction.do?Nr=avl%3auk&N=42 94952692&in_dim_search=1&name=SiteStandard&forwardingPage=line&R=0138262
Hi Kevin I believe I have given you the wrong link, Try http://rswww.com/cgi-bin/bv/rswww/searchBrowseAction.do?Nr=avl%3auk&N=42 94952692&in_dim_search=1&name=SiteStandard&forwardingPage=line&R=38726
Some Jamar cylinder's had poor machining on the bores, Definitely worth checking, When checking the bore's also check the seals, On my first cylinder I had mis-match seals of different materials, thi
Hi Ferg It's a fairly standard MAP sensor originally from General Motors http://www.robietherobot.com/storm/mapsensor.htm I fitted mine on the inside of the firewall with two MS21047-L06 nuts and sui
David You are correct about locating the aerials above your head for best reception; IMHO two people would block most of the signals from the rear if the aerial is sited in the instrument panel, As f
Both of my aerials for Garmin and Honeywell are mounted there, they have no trouble tracking the satellites even in the garage, I take it that anyone who has mounted their aerial overhead has mounted
It will be twelve, Click on the GPS status page and you will see how many its tracking Regards Ivor I have had periods of drop out from my Skymap, which on reflection have mainly been North to South
Craig I have kept the cables as well as using turnbuckles to keep it centered Mod 11510 allow's retaining the cables, Regards Ivor I have done the replacement of the elevator mass balance arm, using
Hi Jos I used Vauxhall/Opel/GM Part number 90572595 spring clamps, I have used Silicone hoses on my 914 which are slightly thicker than the stock Rotax hose, But these clips are suitable for both typ
I was under the impression that its Tygon unless somebody knows better, Roger confirms that the transparent pipe supplied by Europa has not been PVC since 1998. I do not remember the exact material n