Ira I have replaced the Bing for my Jabiru 3300 in the Europa Mono with an Aerocarb so that I can lean. 10,000 to 12,000 feet is not uncommon here in the West. Tom Friedland N96V Atascadero, CA Thank
" I put a single strobe on the tail fin and a single position light in the rudder to reduce the power requirements for this reason." Aye, so did I. I also added the strobe/taillight to the rudder as
"[ both sides of the upper ''D'' shape bulkhead." Hmm, yes, I think I will do that although my manual with any revisions that I have found did NOT say do both sides of the D bulkhead. The language wa
Hi John My vents go into the top of the fuel filler. Then another vent from there goes straight down, through the baggage shelf and exits out the slot for the flap drive. It faces forward to get some
Paul I used 1/4'' OD aluminum tubing. (I have only one vent from the vacuum breaker in the filler tube.) The mesh is a little stainless wool, a bit of 5 minute on it and then just pushed into the end
Hi Fred Move.. No snow plows, no geese. 70 degrees here today. Sure could use some rain. Only 7 inches since last April. We need to dust things occasionally. Put your vent in the flap drive slot. Pro
Hi Fred and John I used the mod 33 drains for my mono but recessed them so they do not extend out in the airstream. That removes a tiny bit of drag (all drag is bad) as well as prevents them from bei
John, I think it is epoxy gelcoat! Sorry about not getting the Jab photos out. I'll get to it. Tom Hi Neville, The "University of Neville" leads us through the fog once again! So, the white stuff on
Hi Ron I followed the advice of another (Eric Trombley?) and Dennis Vories and replaced the tailwheel with a sealed bearing wheel by Colson and the outrigger wheels with sealed bearing wheels by the
Hi Paul A cd works great! (AOL is good for something!) Tom Hi all, I am installing a GX60 and I seem to recall a minimum size requirement for the GPS antenna, however upon scouring the installation m
Hi Brian Try: www.killacycle.com/Lights.htm (The Lights has a capital L) I received their LED combo kit and it is of excellent quality. I have made my own mounts for the landing lights to go in the L
Can anyone enlighten me on positioning our transponder stubb antenna? We have a microair T2000 transponder. They have suggested to us we should limit the co-ax cable to 6 feet due signal loss. This w
Hi Erich Did you mount the inertial reels on the same anchor point that the Europa harnesses use? How much did they cost. I couldn't find a price list. Thanks Tom Friedland A 079 N96V XS mono Jabiru/
Hi John I have used clear polyurethane tubing that is impervious to fuel. It is kind of neat because you can see the level of fuel as you fill. Do you have an ETD for the mono trailer? Tom Friedland
Brian You can get the same Whelen made strobe electronics for about half the price that Whelen charges for their units made for airplanes. I think I got mine from strobes.com. If you don't find them,
Brian Try http://www.strobesnmore.com/ I think that is where I got my Whelen power supply. Works great. I am using it with a fin top streamlined strobe and another in the trailing edge of the rudder.
--From AC Spruce. It was a little over $100 USD. Tom Where did you get the streamlined fin-top strobe that you refer to? am the think requirements, know would typical == == == ==
Hi Joe Why don't you ask John Hurst in Lakeland about the rivet nos. If anyone in the US knows, he should. I wondered the same thing back then and eventually used something else. Tom Hi List, Need so
Hi Jeff Yes, I have an extra set of Graham's lenses. They are very well made. I tried to make my own too and did succeed in making several but I was not happy with them. Graham's are much better and