Hi ALL. No nothing about physics, I am sure all the ways suggested work, nice and simple, but maybe a little crude , however I like simple solutions but many C of A aeroplane have moving aileron trim
Hi All. Peter sounds like you have it sorted, but you are a builder. I may try to find a model maker who can make me a little teardrop bulge with servo and tab, I can , ( you see if you not a builder
Hi All. Some wonderful ideas , Blue Tooth, they would all work fine, but for the none builder my glue on radio servo would do the trick, However a small increase in weight would be there and I had no
Hi Alain I like your set of springs great idea, nice of you to post the photo,s. Think I could manage that one Ok, Many thanks. Alan Read this topic online here: http://forums.matronics.com/viewtopic
Hello All My engine is the 914 turbo charged engine. I have an MGL Flow Meter Gauge. Two Floscan Model 201A-6 Flow Senders, rated up to 30 gallons per hour. These are approved by the LAA and my flow
Hi David, Can't see my last post. will do it again if it does not show up.!!!! However if I had built the plane I would have placed the flow pipe the higher clip along the tunnel and the return runni
What do you call a reasonable price. I understand these things cost around 87,000 to build in kit parts and engine and prop and nav aids. So what is a reasonable price, ????? I paid 36k for mine and
Hi. All Had my permit inspection today all was well, however my inspector found where the inner cable attaches to the carburettor lever arm, the little nut and bolt with the hole in it did not rotate
Hi Remi. Hope you are well, I have had a bad year after meeting you at Sywell last year, remember my little dog Sunny he died in my arm on boxing night the 26th December he was only 8 and it has hit
Hi All. Just had my permit done, the only maintenance I can see is to grease the lead screw. However my spinner rotates un-evenly, i can only put the spinner on the same way round as the screws only
Hello All. I have a Europa Mono converted into a Tri Gear, I have noticed when the nose wheel is off the ground, and you grab hold of the tyre, there is some sideways movement, ie not on the wheel be
Hi. Can get Europa Home Page. etc etc Can,t find manuals. Can you post link. Regards. Alan Read this topic online here: http://forums.matronics.com/viewtopic.php?p=429476#429476
Hi All. Many thanks for the web link, I can see the nose wheel assembly, I have a spring damping system and no bungee straps. My nose wheel is fairly stiff, I don,t know if its 20 lbs or a bit more,
Many thanks All. My nose wheel assembly has no bungee straps but modified by springs. It also has the speed kit fit to it, so you can not see the actual metal leg. I find the drawings on this part no
Hello ALL I went up to the LAA Rally at Sywell on Saturday. A couple of Europa owners explained the nose gear in detail. I have down loaded the manual on nose gear, but I can not find the adhesive us
Hi Brian. "As the nose leg is supplied by the factory already assembled it would best to ask them what they used." Yes, I better do that, but why has a factory made and assembled . component have mov
Hi All. Phoned Europa, its Loctite 638 used. However so far I have tightened the two bolts on the leg strut and the movement is now down to about 1/4" where the tyre meets the ground. Will take spats
Hi . A member completed his IMC rating on a Europa, I am still not sure if this possible, and not going to post on it, However I received an 869 page document from the CAA, There were so many vague p
Get the 869 page document's and don,t be so rude , I remember you rude comments last time, there is no need to post rude comments, Perhaps you can find out if the instruments and avionics have to be
David It is not all as you think, to be exact there a many variables involved in what you can and can't do, involved in adding ratings to your licence. And I am not posting on this again. However the