I am not sure who requested the info on the location of the door strut attachment point for reversed mounting of the door strut but here goes. To determine this location it is best to follow the manu
Author: Erich D Trombley <erichdtrombley@juno.com>
Date: Tue, 13 Nov 2001 16:56:08
I have heard some discussions on the Warp Drive wide blade vs. the narrow blades for the 914. I am looking to order the Warp Drive propeller and need to know the following: In Aircraft Spruce they me
Author: Erich D Trombley <erichdtrombley@juno.com>
Date: Mon, 14 Jan 2002 17:09:59
After you lay up the splash molding do not remove it from the top fuselage until you drill two alignment holes for future alignment of the splash molding and cleco in place from the outside of the fu
Author: Erich D Trombley <erichdtrombley@juno.com>
Date: Wed, 20 Feb 2002 14:27:44
I also have a 914 and the Rotax manual shows grouding at both ends. My manual is three years old though so I don't know if Rotax has changed this or not. Erich Trombley A028
Just curious, of those that are using the PPS AoA, did you decide on the pro or sport versions? Quite abit difference in cost. I purchased only the sensors portion of the kit as I have yet to make up
Michael, I am not sure about a recommended place as the installation manual does not give any direction on this matter. I just ran my ground wire tonight and the location I chose was the magneto moun
Gary, do you know the part number. I have looked on Summit's web page and can only find a silver fire sleeve that is 5/15 I.D. not big enough for the oil lines unfortunately. Thanks Erich Trombley
Another method would be to mount the nut plate on the top surface of the tunnel. Basically drill a hole equal to the outside diameter of the nut plate to allow it fit flush to the top skin. Next remo
Mark, A very ambitious project indeed. I thought the metal work looked great. It never ceases to amaze me at the depth of the talent we have in this forum. Keep us posted on the results. I am definit
Author: Erich D Trombley <erichdtrombley@juno.com>
Date: Fri, 22 Mar 2002 16:52:40
Hi all, Quick question. What are the dimensions of the feltner strips on the anit-servo tab. I am building a classic and my manaul does not specify this later mod? Thanks. Erich Trombley A028 Las Veg
Author: Erich D Trombley <erichdtrombley@juno.com>
Date: Wed, 3 Apr 2002 13:26:34
To all those folks out there that are smarter than I when it comes to electronics here is my question. Does anyone know of either a kit/design or an off the shelf item that will limit the time the ge
Author: Erich D Trombley <erichdtrombley@juno.com>
Date: Tue, 30 Apr 2002 13:39:55
Hello all. I am in the process of wiring my Europa panel and wasn't sure how to proceed with the RC Allen connector for the lighted artificial horizon. The connector, MS3116E8-4S, is a four pin unit
Author: Erich D Trombley <erichdtrombley@juno.com>
Date: Wed, 1 May 2002 15:59:06
Thanks John and Fred for your replies. After reading about having to "exercise" the unit I am a little concerned as it has been in storage for at least two years. Now, it seems that it might have bee
Author: Erich D Trombley <erichdtrombley@juno.com>
Date: Fri, 3 May 2002 15:28:01
Quick question for all of you electronics wizards out there. Bob Nuckells suggests a IN4005 diode accross the alternator relay. My question is will a IN4006 work in its place? Unfortunately, this is