Does anyone know if Arplast have appointed a UK agent yet.Also has anyone f ound =0Aa source of the correct grease to pack the bearings of the PV50 var iable pitch =0Apropeller.=0ACheers Ken.
Glenforsa,Isle of Mull - you can camp and obtain mogas from the local garag e.Look in Pooleys and ring David Howitt. If the weather is good Glenforsa i s magical! If you need mogas at Cark I can brin
We also enjoyed the DOTH to Swansea yesterday. We flew from Cark to Lands E nd. The lady there was very helpful and the breakfast in a bun was excellen t. I am sorry we were a bit late into Swansea-W
Hi,=0APV50 -If you find your problem is the pitch-change motor and you find a supplier then I would like to have the details so that I can buy a spare .=0AIt is possible to fit a resistor in the pink
Hi, =0APV50-If you find your problem is the pitch-change motor,and you find a supplier,I would like to have the details so that I can buy a spare=0AIt is possible to fit a resistor in the pink supply
Funkwerk with associated wiring harness from LX avionics has worked for me. =0A=0AKen- Atkinson=0A=0AG-CEKV=0A =0A=0A________________________________ =0A From: Richard Iddon <riddon@sent.com>=0ATo: E
I am using Aerolube from Skydrive -advertised for Rotax 912/914????=0A=0AKe n Atkinson- G-CEKV=0A =0A=0A________________________________=0A From: "am i-mcfadyean@talktalk.net" <ami-mcfadyean@talktalk
Hi, =0A-- Sorry this is a bit late.=0A--Are th ere any other Europas likely to attend Castle Kennedy Fly-in tomorrow.=0A -- I am flying in in the morning.=0A--=0A-- I thoro ughly enjoyed it last year
Hi Guys, Can anyone confirm the trading state of Arplast. If they really are no longer trading and no one else takes over then all us Arplast propeller users are on our own! I believe we can --Origin
Hi Guys, Can anyone confirm the trading status of Arplast? If they are not now trading then all of us that use the PV50 are without support. We can service the hub easily enough as the bearings are s
Hi Kevin, I would appreciate --Original message-- Date : 19/09/2015 - 19:46 (GMTDT) To : europa-list@matronics.com Subject : Re: Europa-List: Arblast PV 50 Prop. CS Motor, Hi Ken, I have details of t
Hi Kevin, I would appreciate the details of the PV50 motor.Do you know where to obtain a replacement? I also have some spare blades but they are not matched to my hub, therefore ,if I needed to use t
Author: Ken Atkinson <kennethatkinson178@btinternet.com>
Date: Mon, 21 Mar 2016 22:18:19
Hi Jon, I have the Arplast and have had some vibration issues that sound similar to your own. I have found some wear in the small square nylon blocks and also in the brass 6 mm actuator screw. I am m
Author: Ken Atkinson <kennethatkinson178@btinternet.com>
Date: Sun, 12 Feb 2017 21:17:55
Hi Jon, If something is loose inside your PV50 you must dismantle it again and investigate. The initial balancing, I believe, would have been achieved by fitting appropiate weights into the centre of
Author: Ken Atkinson <kennethatkinson178@btinternet.com>
Date: Thu, 4 Apr 2019 10:19:46
I also have been using the Odyssey PC680 for 10 years with no problems. I have just purchased one from Tayna, it arrived next day after ordering. They say the PC680 life is 3 to 12 years but I feel 5
Author: Ken Atkinson <kennethatkinson178@btinternet.com>
Date: Mon, 5 Aug 2019 22:37:48
Is the list still active ,I can't seem to connect? Ken. -- This email has been checked for viruses by Avast antivirus software. https://www.avast.com/antivirus